Prakai's Wiki, eduroam-TH SP Monitoring
From Prakai Nadee
eduroam-TH SP Monitoring firmware installation for WEMOS LOLIN32
Wemos Lolin board (ESP32 with 128x64 SSD1306 I2C OLED display)
- ESP32-based (ESP-WROOM-32 240MHz)
- USB Micro, CP2102 USB to UART bridge
- 4MB SPI flash memory + 520K RAM
- 1 Button, Classic 0.96” (168×64 pixels) monochrome OLED display, 1 Reset
- 2.4G Antenna max sensitivity reception: -97 dBm
- 5V DC power supply
- Development Platform MicroPython, Arduino
Where to buy
- ฿380, ESP32 + OLED 128x64 on one board บอร์ดพัฒนา ESP32 พร้อมจอ OLED380, ESP32 + OLED 128x64 on one board บอร์ดพัฒนา ESP32 พร้อมจอ OLED
- ฿470, บอร์ดพัฒนา IoT พร้อมจอ OLED Wemos® Lolin32 ESP32 + OLED WiFi+Bluetooth
How to flash eduroam-TH SP Monitoring firmware for WEMOS LOLIN32
System requirement
- Desktop/Labtop computer
- Microsoft Windows 8, 10
- Windows PowerShell
- USB port
Instruction
- Download eduroam-TH firmware and flashing tool
- Extract the downloaded file to a local disk (ex: D:\):
- List of files:
D:\eduroam-TH-firmware\ - esptool.exe - Lolin32.ps1 - ESP32-eduroam-mon.ino.lolin32.bin - ESP32-eduroam-mon.ino.partitions.bin - boot_app0.bin - bootloader_dio_80m.bin
- Run Windows PowerShell: Win+r >> PowerShell.exe
Windows PowerShell Copyright (C) Microsoft Corporation. All rights reserved.
PS C:\Users\Hello World> _
- Change location to D:\duroam-TH-firmware
PS C:\Users\Hello World> D: PS D:\> cd eduroam-TH-firmware PS D:\eduroam-TH-firmware> _
- Enable execution of PowerShell scripts
PS D:\eduroam-TH-firmware> Set-ExecutionPolicy -Scope CurrentUser -ExecutionPolicy Unrestricted -Force
- Run the flashing script: Lolin32.ps1 and follow the instruction
PS D:\eduroam-TH-firmware> .\Lolin32.ps1 ===================================================================== =============== eduroam-TH monitoring device flash tool =============== =======================================================================
1) Connect Wemos LOLIN32 to computer
Press Enter to continue...:
- Connect Wemos LOLIN32 to USB of computer
======================================================================= =============== eduroam-TH monitoring device flash tool =============== =======================================================================
2) Select a COM port
1: Silicon Labs CP210x USB to UART Bridge (COM111) 2: Standard Serial over Bluetooth link (COM5) 3: Standard Serial over Bluetooth link (COM6) 4: Standard Serial over Bluetooth link (COM3) 5: Standard Serial over Bluetooth link (COM4) Q: Press 'Q' to quit.
Please select COM port: 1
- Firmware flashing starts, Long press BOOT button if flashing does not start in 5 seconds
======================================================================= =============== eduroam-TH monitoring device flash tool =============== =======================================================================
3) Long press BOOT button if flashing does not start in 5 seconds
Flashing: Silicon Labs CP210x USB to UART Bridge (COM111) ======================================================================= esptool.py v2.6 Serial port COM111 Connecting.... Chip is ESP32D0WDQ6 (revision 1) Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None MAC: c4:4f:33:0c:11:bd Uploading stub... Running stub... ... Leaving... Hard resetting via RTS pin...
- Device reboot and running
======================================================================= 4) Disconnect Wemos LOLIN32 from computer to stop serial monitor =======================================================================
eduroam-TH SP monitoring device version 0.30-2019103100 ESP32 Development Board: LOLIN32 ... Connecting WiFi to: eduroam Security Type: WPA2 Enterprise ............................. WiFi connection successfully ... Wifi will disconnect and reconnect again in 30 minutes Going into DeepSleep mode and will wake up in 30 minutes
- Disconnect Wemos LOLIN32 from computer
How to use
--- Please wait ---
