Prakai's Wiki, eduroam-TH SP Monitoring
From Prakai Nadee
eduroam-TH SP Monitoring firmware installation for DOIT ESP32 DEVKIT V1
DOIT ESP32 DEVKIT V1
- ESP32-based (ESP-WROOM-32 240MHz)
- USB Micro, CP2102 USB to UART bridge
- 4MB SPI flash memory + 520K RAM
- 1 Button, 1 Reset
- 2.4G Antenna
- 5V DC power supply
- Development platform: MicroPython, Arduino
Where to buy
Where to buy
- ฿240, DOIT ESP32 DevKit V1 Development Board WiFi + Bluetooth
- ฿300, ESP32 DOIT ESP32 DEVKIT V1 ESP-32S NodeMCU ESP-WROOM-32 Wi-Fi and Bluetooth Dual Core ESP-32 ESP-32S ESP 32
How to flash eduroam-TH SP monitor firmware for DOIT ESP32 DEVKIT V1
System requirement
- Desktop/Labtop computer
- Microsoft Windows 8, 10
- Windows PowerShell
- USB port
Instruction
- Download eduroam-TH firmware and flashing tool
- Extract the downloaded file to a local disk (ex: D:\):
- List of files:
D:\eduroam-TH-firmware\ - esptool.exe - DoITDevKitV1.ps1 - ESP32-eduroam-mon.ino.doitESP32devkitV1.bin - ESP32-eduroam-mon.ino.partitions.bin - boot_app0.bin - bootloader_dio_80m.bin
- Run Windows PowerShell: Win+r >> PowerShell.exe
Windows PowerShell Copyright (C) Microsoft Corporation. All rights reserved.
PS C:\Users\Hello World> _
- Change location to D:\duroam-TH-firmware
PS C:\Users\Hello World> D: PS D:\> CD eduroam-TH-firmware PS D:\eduroam-TH-firmware> _
- Run the flashing script: DoITDevKitV1.ps1 and follow the instruction
PS D:\eduroam-TH-firmware> .\DoITDevKitV1.ps1 ===================================================================== =============== eduroam-TH monitoring device flash tool =============== =======================================================================
1) Connect DoIT ESP32 DevKitV1 to computer
Press Enter to continue...:
- Connect DOIT ESP32 DEVKIT V1 to USB of computer
======================================================================= =============== eduroam-TH monitoring device flash tool =============== =======================================================================
2) Select a COM port
1: Silicon Labs CP210x USB to UART Bridge (COM111) 2: Standard Serial over Bluetooth link (COM5) 3: Standard Serial over Bluetooth link (COM6) 4: Standard Serial over Bluetooth link (COM3) 5: Standard Serial over Bluetooth link (COM4) Q: Press 'Q' to quit.
Please select COM port: 1
- Firmware flashing starts, Long press BOOT button if flashing does not start in 5 seconds
======================================================================= =============== eduroam-TH monitoring device flash tool =============== =======================================================================
3) Long press BOOT button if flashing does not start in 5 seconds
Flashing: Silicon Labs CP210x USB to UART Bridge (COM111) ======================================================================= esptool.py v2.6 Serial port COM111 Connecting.... Chip is ESP32D0WDQ6 (revision 1) Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None MAC: cc:50:e3:99:1b:48 Uploading stub... Running stub... ... Leaving... Hard resetting via RTS pin...
- Device reboot and running
======================================================================= 4) Disconnect DoIT ESP32 DevKitV1 from computer to stop serial monitor =======================================================================
eduroam-TH SP monitoring device version 0.30-2019103100 ESP32 Development Board: doitESP32devkitV1 ... Connecting WiFi to: eduroam Security Type: WPA2 Enterprise ............................. WiFi connection successfully ... Wifi will disconnect and reconnect again in 30 minutes Going into DeepSleep mode and will wake up in 30 minutes
- Disconnect DOIT ESP32 DEVKIT V1 from computer
How to use
--- Please wait ---
